- whatsapp +51955515985
- support@ecuforcetruck.com
- 24/7 Customer Support
Menu
Shop
Account
Subtotal: $0.00
No products in the cart.
Circuit Description
The EGR temperature sensor is a variable resistor sensor and is used to measure the temperature of the EGR gas flow after it exits the EGR cooler. The engine control module (ECM) supplies 5 volts to the EGR temperature signal circuit. The ECM monitors the change in voltage caused by changes in the resistance of the sensor to determine the EGR flow temperature.
The EGR temperature value is used by the ECM for the engine protection system and engine emissions control.
Component Location
The EGR temperature sensor is located on the EGR connection tube between the EGR cooler and the air intake connection.
Conditions for Running the Diagnostics
This diagnostic consists of two parts. The first part runs when the keyswitch is turned to the ON position after a 10 hour cold soak, during which the keyswitch has been turned OFF. The second part runs continuously while the engine is operating and EGR flow is above a calibratible value.
Conditions for Setting the Fault Codes
The fault code is set active when an EGR temperature reading too high or too low for the operating conditions has been detected, or if the EGR temperature reading is not changing with the operating conditions.
Action Taken When the Fault Code is Active
The ECM illuminates the red STOP ENGINE light and/or the malfunction indicator lamp (MIL) immediately when the diagnostic runs and fails.
Diesel exhaust fluid injection into the aftertreatment system is disabled.
Active and stationary regeneration of the diesel particulate filter will be disabled.
The EGR valve will be closed.
Engine torque will be reduced if the engine is operated for an extended period of time with this fault active.
Conditions for Clearing the Fault Code
To validate the repair using a Diagnostic Road Test, utilize a route that incorporates both stop-and-go city driving and steady state highway driving. It may be necessary to load the unit for certain diagnostics in the ECM to run.
To validate the repair using a Chassis Dynamometer Test, utilize a routine that incorporates acceleration and motoring events, steady state highway operation, and load. This will simulate normal driving and allow the diagnostics in the ECM to run.
If the fault code does not go inactive after 10 minutes of driving, it may be necessary to perform a 10 hour cold soak with the key OFF, then turn the keyswitch to the ON position so that the key ON portion of the diagnostic will run.
The fault code status displayed by INSITE? electronic service tool will change to INACTIVE immediately after the diagnostic runs and passes.
The ECM will turn off the amber CHECK ENGINE lamp after the diagnostic runs and passes.
For OBD engines, the ECM will turn off the MIL after three consecutive trips where the diagnostic runs and passes.
The ?Reset All Faults? command in INSITE? electronic service tool can be used to clear active and inactive faults, as well as extinguish the MIL for OBD applications.
Shop Talk
Possible causes of this fault code include:
Stuck in-range EGR temperature sensor
High resistance in the EGR temperature sensor SIGNAL or RETURN wires
Possible Cause:
1) ECM failure
Related
Categories Cumminz, DTC TRUCKS, ISX15 CM2250 (2010-12)Tags 1867, 2, 2010-12, 412, CM2250, Code, Cummins, Data, Engine, Erratic, Fault, FMI, Gas, Incorrect, Intermittent, ISX15, or, PID, Recircuilation, SPN, Temperature-
Wiring Diagrams
Component Locators
- Volvo Premium Tech Tool PTT 2.8.130 Diagnostic Software 04.2022 ACPI ( 1 PC )
Trucks software$143.00
Rated 0 out of 5
CAT$50.00
Rated 0 out of 5
- 2021 VOLVO PREMIUM TECH TOOL PTT V2.8.21 VCADS+DEVELOPER TOOL+APCI 2021/09 ( 1 PC )
Trucks software$85.00
Rated 0 out of 5
- Hino Diagnostic eXplorer 2 – Hino DX2 1.1.19.1 with keygen unlocked ( Hino trucks )
Hino$50.00
Rated 0 out of 5
- Magic Tuner Flash Tool v2.1
Magic Tuner$180.00
Rated 0 out of 5
- VOLVO PREMIUM TECH TOOL PTT 2.7.30 Developer + Devtool + INSTALATION VIDEO!
Trucks software$60.00
Rated 0 out of 5
- 2021 VOLVO PREMIUM TECH TOOL PTT V2.8.21 VCADS+DEVELOPER TOOL+APCI 2021/09 ( 1 PC )
Trucks software$85.00
Rated 0 out of 5
JPRO$94.00
Rated 0 out of 5
- DETROIT DDDL 8.14 SP3 – Detroit Diesel Diagnostic Link 8.14 SP3 2021 ( 1PC )
Detroit$73.00
Rated 0 out of 5
- PACCAR Electronic Service Analyst 5.4.3.0 SW files 27.03.2021 software trucks
PACCAR$60.00
Rated 0 out of 5
- Diesel Diagnostic Link 8.17 SP1 2023
Detroit$96.00
Rated 0 out of 5
- Isuzu E-IDSS Diagnostic Service System 04.2022 ( 1 PC )
ISUZU$126.00
Rated 0 out of 5
- Allison DOC 2021 V2 (1PC)
Allison$67.00
Rated 0 out of 5
- Volvo Penta EPC 6 Offline VMware [12.2021] VMware
Trucks software$64.00
Rated 0 out of 5
- Perkins EST 2021B v1.0 Active License + FPKG ( 1 PC )
CAT$75.00
Rated 0 out of 5
- Thermo King EPC 2012
Thermo King$45.00
Rated 0 out of 5
- DOWNLOAD Paccar ESA Electronic Service Analyst 5.5.0 Diagnostic Software 2023
PACCAR$96.00
Rated 0 out of 5
- Perkins SPI2 2018A Dealer Parts and Service
Perkins$50.00
Rated 0 out of 5
- Detroit Diesel Diagnostic Link DDDL 6.50 ( software trucks )
Detroit$20.00
Rated 0 out of 5
- Caterpillar ET 2022A Electronic Technician + Factory Password (1PC)
CAT$96.00
Rated 0 out of 5
Related products
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
- PACCAR PX-9 CM2350 (2013-17) Fault Code:3634 PID: SPN:5484 FMI:4 Engine Fan Clutch 2 Control Circuit – Voltage Below Normal or Shorted to Low Source
DTC TRUCKS
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
- SERVICE MANUAL DETROIT DD15 GHG 17
DETROIT$42.00
Rated 0 out of 5
- MANUAL SERVICE DEUTZ AGROCOMPACT F60 – 70F3 – 70F4 – F80 – F90
DEUTZ$34.00
Rated 0 out of 5
- SERVICE MANUAL DDEC VI Troubleshooting Guide – MBE4000 6SE568
DETROIT$40.00
Rated 0 out of 5
- SERVICE MANUAL BOBCAT 610-611 sms
BOBCAT$45.00
Rated 0 out of 5
- SERVICE MANUAL BOBCAT 974-975 sms
BOBCAT$35.00
Rated 0 out of 5
- MANUAL SERVICE DEUTZ AGROTRAC 110-130-150
DEUTZ$20.00
Rated 0 out of 5
INTERNATIONAL ENGINES$24.00
Rated 0 out of 5
- SERVICE MANUAL Mack MP10
MACK$29.00
Rated 0 out of 5
- SERVICE MANUAL BOBCAT 1213 sms
BOBCAT$30.00
Rated 0 out of 5
- Allison 1000 and 2000 Series Gen 4 (2005-11) Service manual
Allison$10.00
Rated 0 out of 5