- DOWNLOAD ISUZU E-IDSS software 7.2021 [Diagnostic Isuzu Industrial Engines] truck
$88.00Add to cart
- DOWNLOAD Eaton Service Ranger 4.9 Engineering 4.9 [05.2021] Engineering Level ( 1 PC )
$50.00Add to cart
- DOWNLOAD CAT ET 2021A (Caterpillar Electronic Technician) + Factory Password (1 PC )
$64.00Add to cart
- Description
- Tags
- Reviews (0)
Description
Circuit Description
An algorithm in the ECM calibration monitors engine speed as each injector fires while the engine is at idle. If a cylinder has high or low contribution to engine speed, this fault will become active. The intention of this fault is to assist in troubleshooting performance complaints such as engine misfire and low power.
Component Location
The ECM is located on the intake side of the engine.
Conditions for Running the Diagnostics
This diagnostic runs continuously when the engine coolant temperature is greater than 71?C [160?F].
Conditions for Setting the Fault Codes
If cylinder 6 has high or low contribution to engine speed, this fault will become active.
Action Taken When the Fault Code is Active
The ECM illuminates the amber CHECK ENGINE lamp and/or the Malfunction Indicator Lamp (MIL) immediately when the diagnostic runs and fails.
Conditions for Clearing the Fault Code
To validate the repair, start the engine and let it idle for up to 5 minutes.
The fault code status displayed by INSITE? electronic service tool will change to INACTIVE immediately after the diagnostic runs and passes.
The ECM will turn off the amber CHECK ENGINE lamp after the diagnostic runs and passes.
For On-Board Diagnostic (OBD) engines, the ECM will turn off the MIL after three consecutive trips where the diagnostic runs and passes.
The ?Reset All Faults? command in INSITE? electronic service tool can be used to clear active and inactive faults, as well as extinguish the MIL for OBD applications.
Shop Talk
If Fault Code 1659 is inactive in the ECM memory and there is no complaint such as ?low power? or ?engine misfire?, it is possible that an intermittent event, such as air entering the fuel system, following a filter change caused the fault. Inactive counts of Fault Code 1659 should be disregarded unless other performance symptoms are present. The engine coolant temperature must be greater than 71?C [160?F] before this diagnostic will run.
Causes of cylinder misfire can include:
Valve lash out of specification (compare actual valve lash to reset limits)
Cylinder malfunction (check for high blowby when the engine is loaded)
Valve malfunction or valve held open (listen for intake valve ?chirping? noise in the intake)
Cylinder head or gasket malfunction (look for signs of oil, coolant, or casting flash in the intake or exhaust passages)
Extreme camshaft wear (inspect the camshaft lobes for wear)
Extra, missing, or damaged sealing washer under an injector
Injector malfunctions (?swap? injectors to see if the problem ?follows? the indicated injector).
Check air compressor timing (if engine has had fault since new or has had a recent air compressor replacement).
Possible Cause:
1) Cylinder Misfire failure
2) ECM calibration
Related
Tags: 1328, 1659, 2010-12, 31, 6-, CM2250, Code, Condition, Cummins, Cylinder, Engine, Exists, Fault, FMI, ISX15, Misfire, PID, SPN
Reviews
There are no reviews yet.
Be the first to review “Cummins ISX15 CM2250 (2010-12) Fault Code: 1659 PID: SPN: 1328 FMI: 31 Engine Misfire Cylinder 6- Condition Exists”
Categories Cumminz, DTC TRUCKS, ISX15 CM2250 (2010-12)Tags 1328, 1659, 2010-12, 31, 6-, CM2250, Code, Condition, Cummins, Cylinder, Engine, Exists, Fault, FMI, ISX15, Misfire, PID, SPN
- See AlsoDetroit DD15 GHG14 (2014-16) Fault Code: SPN 1328 FMI 31 (MCM) Idle Smoothness Control/Cylinder #6 Misfire At Idle - EcuForce TruckCummins ISX12 CM2250 (2010-12) Fault Code: 1659 PID: SPN: 1328 FMI: 31 Engine Misfire Cylinder 6- Condition Exists - EcuForce TruckCummins ISX11.9 CM2250 (2010-12) Fault Code: 1659 PID: SPN: 1328 FMI: 31 Engine Misfire Cylinder 6- Condition Exists - EcuForce TruckDOWNLOAD Caterpillar SIS 2021 Full Service Dealer
$95.00Add to cart
- DOWNLOAD IDSS Isuzu G-IDSS 2020 Diagnostic Service System [08.2020] Release Full
$125.00Add to cart
- DOWNLOAD VOLVOUU PREMIUM TECH TOOL PTT 2.7.30 Developer + Devtool + INSTALATION VIDEO!
$60.00Add to cart
- Related Products
Quick View
Add to wishlist
CompareAdd to cart
AllisonDTC TRUCKS
Quick View
Add to wishlist
CompareAdd to cart
AllisonDTC TRUCKS
Quick View
Add to wishlist
CompareAdd to cart
AllisonDTC TRUCKS
Quick View
Add to wishlist
CompareAdd to cart
AllisonDTC TRUCKS
Quick View
Add to wishlist
CompareAdd to cart
AllisonDTC TRUCKS
JPRO
DOWNLOAD Noregon JPRO Commercial Fleet Diagnostics 2017 v3 (Copy)$40.00Add to cart
cummisznn
Cumminmms Insite pro 8.9 Diagnostic Software$80.00Add to cart
Trucks software
JPRO Diagnostic Software Download 2024$100.00Add to cart
Trucks software
AGCO EDT 2023.10 Electronic Diagnostic Tool 1.125$120.00Add to cart
Trucks software
DOOSAN diagnostic software DMS-5 3.1.3 [2023.11] 1PC$106.00Add to cart
Trucks software
Bendix Acom Pro 2023 V1 diagnostic software 1PC$83.00Add to cart
Trucks software
VOLVOUU PTT TECH TOOL 2.8.220 2023 Last version 1pc$200.00Add to cart
Trucks software
Download Allison Doc Premium Update 2023 v2$105.00Add to cart
CAT
DOWNLOAD CAT ET 2022A Advanced diagnostic software for Caterpillar equipment$85.00Add to cart
JPRO
DOWNLOAD Noregon JPRO Commercial Fleet Diagnostics 2017 v3$40.00Add to cart
INTERNATIONAL ENGINES
SERVICE MANUAL I2017 International® A26 Engine$45.00Add to cart
EATON
SERVICE MANUAL EATON UltraShift PLUS$45.00Add to cart
BOBCAT
SERVICE MANUAL BOBCAT 335 sms$45.00Add to cart
Allison
DOWNLOAD Allison DOC 2021 V2 (1PC)$65.00Add to cart
BOBCAT
SERVICE MANUAL BOBCAT 741-742-743-743ds sms$45.00Add to cart
TRUCK MANUALS
SERVICE MANUAL DAF LF45, LF55 Series Workshop Manual$45.00Add to cart